# Back up and restore static IP and DNS settings

> Save an adapter's IP, gateway, and DNS settings to a file with S.A.K. Utility, then restore them on the same PC or another one.

Source: https://sakutility.com/wiki/back-up-network-settings
Applies to: S.A.K. Utility (SAK), a free portable Windows toolkit
Updated: 2026-11-09

To back up a network adapter's IP and DNS settings, use S.A.K. Utility: go to the **Network Management** tab, open **Network Adapters**, select the adapter, and press **Backup Settings**. To put them back, press **Restore Settings** and pick the file. The backup holds the MAC address, the DHCP setting, the IPv4 address and mask, the gateway, and the DNS servers.

## When to use this

- A PC has a hand-set IP address, and you are about to reinstall Windows or replace it.
- You want your own copy before **Reset Network**. Reset Network saves and puts back the settings of every adapter that is turned on, but it cannot read a turned-off adapter's settings.
- You need the same settings on a replacement PC.

## What you need

- For a backup: no special rights.
- For a restore: **administrator rights**. Click **Run as Admin** in the status bar first. Without them, the restore ends with **Restore Incomplete**.

## Steps

### Save a backup

1. Go to the **Network Management** tab and open **Network Adapters**.
2. Click the adapter in the table.
3. Press **Backup Settings**.
4. Choose where to save the file and press **Save**. The suggested name ends in `_settings_backup.json`.

![Save Adapter Settings Backup window with a suggested file name ending in _settings_backup.json](https://sakutility.com/screenshots/wiki/net_backup_save.webp?v=9cdcc09ee3)

*Choose where to keep the backup file*

A **Backup Complete** message shows where the file went. Keep a copy somewhere other than the PC you are about to change.

![Backup Complete message showing the path of the saved file](https://sakutility.com/screenshots/wiki/net_backup_complete.webp?v=16e8849b2e)

*The backup file can restore this PC or another one*

### Restore a backup

> A restore replaces the adapter's current IP settings, and you may lose your connection for a moment. If you restore a static address on a second PC while the first is still on the network, the two will clash.

1. Click **Run as Admin** in the status bar, if the label beside it says **Standard**.
2. Go to the **Network Adapters** tab and press **Restore Settings**.
3. Pick the backup file.
4. If the PC has more than one adapter that can take it, choose one under **Select Target Adapter**. From the right-click menu, the adapter you clicked is chosen to start with. From the **Restore Settings** button, the list starts on the adapter the backup was made from, then on one of the same type (Ethernet, Wi-Fi), and only then on the first in the list.
5. Read the **Confirm Restore** message, and press **Yes**.
6. Wait for **Restore Complete**. The adapter may take a moment to settle.

![Confirm Restore message naming the adapter and warning that its current settings will be overwritten, with Yes and No buttons](https://sakutility.com/screenshots/wiki/net_restore_confirm.webp?v=b34bc125ff)

*Confirm Restore names the adapter that will change*

## How it works

The backup is a small text file in JSON format. It holds:

- the MAC address, which is the adapter's hardware ID
- whether DHCP is on
- the IPv4 address and subnet mask
- the gateway
- the IPv4 DNS servers
- the adapter's name, type (such as Ethernet or Wi-Fi), and description, the computer's name, and the time, so you can tell backups apart

If DHCP was on in the backup, a restore turns DHCP back on, and DNS goes back to automatic. If the settings were static, a restore sets the address, mask, gateway, and DNS servers. It leaves the gateway's priority (its metric) to Windows, as Windows' own adapter settings do, so on a PC with more than one network the restored adapter does not take over the default route.

## Good to know

- The backup does not hold driver details, link speed, or traffic counts. S.A.K. Utility shows those on screen only.
- It does not hold IPv6 settings, Wi-Fi names, or Wi-Fi passwords.
- It keeps one IPv4 address. An adapter with several keeps only one in the backup.
- The MAC address is there for reference. A restore does not change the target adapter's MAC address.
- The right-click menu also offers **Backup Settings...** and **Restore Settings...** for Ethernet and Wi-Fi adapters.
- The restore list holds every network adapter Windows reports, including Wi-Fi and disabled ones, on Windows in any language.
- To move network settings along with a whole user profile, see the profile backup guide below.

## Related guides

- [Set a static IP, DNS, or DHCP on a network adapter](https://sakutility.com/wiki/manage-network-adapters)
- [Reset Winsock and TCP/IP on Windows](https://sakutility.com/wiki/reset-network)
- [Back up a Windows user profile before reinstalling](https://sakutility.com/wiki/back-up-user-profile)
