# Set a static IP, DNS, or DHCP on a network adapter

> Set a static IP, change DNS, switch to DHCP, rename or disable a network adapter from the Network Adapters tab in S.A.K. Utility.

Source: https://sakutility.com/wiki/manage-network-adapters
Applies to: S.A.K. Utility (SAK), a free portable Windows toolkit
Updated: 2026-11-09

To change a network adapter's settings, use S.A.K. Utility: go to the **Network Management** tab, open **Network Adapters**, right-click the adapter, and choose **IP Configuration**. From that menu you can set a static IP address, set DNS servers, or switch back to automatic settings. The same right-click menu can also disable or rename the adapter.

## When to use this

- A printer, server, or similar device needs a fixed address.
- You want a PC to use different DNS servers.
- You want to see everything about an adapter in one place.

A static IP is an address you set by hand. DHCP is the usual automatic setting, where the router hands out an address.

## What you need

- **Administrator rights** for any change. S.A.K. Utility does not ask for them on its own here, so click **Run as Admin** in the status bar first. Without them, the change fails with a message saying that administrator rights are needed.
- The correct address, subnet mask, and gateway for your network, if you are setting them by hand.

Viewing adapters needs no special rights.

## Steps

### See your adapters

1. Go to the **Network Management** tab and open **Network Adapters**.
2. Read the table: **Name**, **Type**, **Status**, **IP Address**, **MAC**, and **Speed**. MAC is the adapter's hardware ID. **Status** reads **No valid address** when the adapter is connected but has only a self-assigned 169.254.x.x address: Windows gave it that because no DHCP server answered and no address is set by hand, so it cannot reach other networks. Point at the status or the address to read why.

   ![The adapter table with the Ethernet adapter's status reading No valid address in orange beside the self-assigned address 169.254.193.132, and the loopback adapter Connected](https://sakutility.com/screenshots/wiki/net_adapter_no_valid_address.webp?v=5d65e12aa3)

*An adapter with only a self-assigned address*

3. Click an adapter to see more below the table, including its gateway, DNS servers, and whether DHCP is on.
4. Press **Refresh Adapters** or `F5` to read them again. Press **Copy Config** to copy the details as text.

![Network Adapters tab with toolbar buttons, a table of adapters, and details of the selected adapter below](https://sakutility.com/screenshots/wiki/net_adapters_table.webp?v=a4bf4a9736)

*The Network Adapters tab with one adapter selected*

### Open the adapter menu

Right-click an adapter. What you see depends on its type. Wi-Fi and Ethernet adapters have **IP Configuration**, and Bluetooth adapters have **View Bluetooth Devices**.

![Right-click menu for an Ethernet adapter with Status, Properties, Disable, Diagnose, IP Configuration, Rename, Copy Configuration, Backup Settings, and Restore Settings](https://sakutility.com/screenshots/wiki/net_adapter_menu.webp?v=73e969cf5d)

*The right-click menu for an Ethernet adapter*

Choose **Status...** for a full report on the adapter: connection, addresses, DHCP lease, traffic counts, errors, and driver details.

![Adapter Status window with General, Connection, IPv4 Configuration, and IPv6 Configuration in view, and more sections further down](https://sakutility.com/screenshots/wiki/net_adapter_status_dialog.webp?v=94daba69b4)

*Status... shows everything Windows reports about the adapter*

Scroll down in that window for **DHCP**, **Statistics**, and **Driver Information**.

### Set a static IP address

> A wrong address can cut this PC off from the network. If you are connected to the PC remotely, you may lose the connection.

1. Right-click the adapter and choose **IP Configuration**, then **Set Static IP...**.
2. Fill in **IP Address**, **Subnet Mask**, and **Gateway**. The boxes start with the current values.
3. Press **OK**.

![Set Static IP window with boxes for IP Address, Subnet Mask, and Gateway, and OK and Cancel buttons](https://sakutility.com/screenshots/wiki/net_static_ip_dialog.webp?v=0aaeb08a8e)

*Set Static IP starts with the adapter's current values*

### Set DNS servers

1. Right-click the adapter and choose **IP Configuration**, then **Set DNS Servers...**.
2. Fill in **Primary DNS**. **Secondary DNS** is optional.
3. Press **OK**.

![Set DNS Servers window with boxes for Primary DNS and Secondary DNS, and OK and Cancel buttons](https://sakutility.com/screenshots/wiki/net_dns_dialog.webp?v=5ec81fb9bf)

*Set DNS Servers takes one required and one optional server*

### Go back to automatic settings

1. Right-click the adapter and choose **IP Configuration**, then **Enable DHCP**. This item appears only when DHCP is off.
2. Press **Yes**. The static settings are removed.

When DHCP is on, the same menu has **Release DHCP Lease** and **Renew DHCP Lease**, which give up the current address and ask for a new one.

### Other menu items

- **Disable** or **Enable** turns the adapter off or on. Disabling asks first, because you may lose your connection.
- **Rename...** changes the adapter's name.
- **Properties** and **Open Adapter Settings** open the matching Windows settings page.
- **Diagnose** starts a Windows network troubleshooter. Where Windows no longer has that troubleshooter, it opens **Settings** at **Troubleshoot** instead and the status bar says so.

## How it works

S.A.K. Utility passes each change to Windows, then reads the adapters again so the table shows the result. The other toolbar buttons, **Backup Settings**, **Restore Settings**, and **Reset Network**, have guides of their own below.

## Good to know

- Static IP and DNS changes here cover IPv4 only.
- The gateway in **Set Static IP...** is the only routing setting. S.A.K. Utility has no route table editor.
- **Set Static IP...** leaves the gateway's priority (its metric) to Windows, as Windows' own adapter settings do, so on a PC with more than one network it does not take over the default route.
- Save the current settings first if you might want them back. See the backup guide below.
- S.A.K. Utility does not create network bridges. To make one, choose **Open Adapter Settings**, select the adapters in the Windows window that opens, right-click, and choose **Bridge Connections**.

## Related guides

- [Back up and restore static IP and DNS settings](https://sakutility.com/wiki/back-up-network-settings)
- [Reset Winsock and TCP/IP on Windows](https://sakutility.com/wiki/reset-network)
- [Look up DNS records and compare DNS servers](https://sakutility.com/wiki/dns-lookup-and-compare)
- [When S.A.K. Utility needs administrator rights](https://sakutility.com/wiki/administrator-rights)
