# Run ping, traceroute, and MTR on Windows

> Check whether a device answers and find where a connection slows down, using the Ping, Traceroute, and MTR tools in S.A.K. Utility.

Source: https://sakutility.com/wiki/ping-traceroute-mtr
Applies to: S.A.K. Utility (SAK), a free portable Windows toolkit
Updated: 2026-11-01

To ping a device, trace the path to it, or run MTR on Windows, use S.A.K. Utility: go to the **Network Management** tab, open **Network Diagnostics**, and choose **Ping**, **Traceroute**, or **MTR**. Type a name or address, press the start button, and results appear as they arrive.

## When to use this

Use these tools when a website, printer, or other device is slow or will not answer.

- **Ping** sends small test messages to one device and times the replies. It answers "can I reach it, and how fast?"
- **Traceroute** lists each router your traffic passes through on the way. Each router is called a hop. It answers "which way does my traffic go?"
- **MTR** repeats that trace many times and keeps totals for each hop. It answers "where along the way am I losing traffic?"

## What you need

- A name or address for the target, such as `example.com` or `192.168.1.1`.
- A working network adapter. To test a website, you also need the internet.

These tools do not ask for administrator rights, and they change nothing on the PC.

## Steps

### Ping a device

1. Go to the **Network Management** tab and open **Network Diagnostics**.
2. Choose the **Ping** tab.
3. Type the name or address in **Target**.
4. Change the options if you need to. **Count** is the number of messages (10 by default), **Timeout** is how long to wait for each reply (4000 ms), **Interval** is the gap between messages (1000 ms), and **Size** is the message size (32 B).
5. Press **Start Ping**. Press **Stop** to end early.

Each row shows the reply's **IP**, **Status** (Reply or Timeout), **RTT (ms)**, and **TTL**. RTT means round-trip time, how long the reply took. A line above the table adds up the run: sent, received, lost, lowest, highest, and average time, plus jitter, which is how much the time varies.

![Ping tab with target 127.0.0.1 and ten rows showing Reply, round-trip time, and TTL, with a summary line above the table](https://sakutility.com/screenshots/wiki/net_ping_result.webp?v=870579aa37)

*Ping results with the summary line above the table*

### Trace the path to a device

1. Choose the **Traceroute** tab.
2. Type the name or address in **Target**.
3. Leave **Max Hops** at 30 unless the path is unusually long.
4. Press **Trace Route**.

Each row is one hop, with its **IP**, **Hostname**, three times (**RTT 1**, **RTT 2**, **RTT 3**), and **Avg (ms)**.

![Traceroute tab with target 127.0.0.1 and one hop listed with its IP address and three round-trip times](https://sakutility.com/screenshots/wiki/net_traceroute_result.webp?v=a3554953e6)

*Traceroute lists one row for each hop*

### Run MTR

1. Choose the **MTR** tab.
2. Type the name or address in **Target**.
3. Set **Cycles**, the number of passes. The default is 100, sent about one per second, so a full run takes at least 100 seconds.
4. Press **Start MTR**. The table updates after each pass. Press **Stop** to end early.

Each row shows **Loss %**, **Sent**, **Avg (ms)**, **Best**, **Worst**, and **Jitter** for one hop.

![MTR tab with target 127.0.0.1 and one hop showing loss percentage, packets sent, and average, best, and worst times](https://sakutility.com/screenshots/wiki/net_mtr_result.webp?v=2a77f37a65)

*MTR keeps totals for each hop*

## How it works

Each tool sends small network test messages and measures what comes back. Nothing is installed, and no settings change.

To read MTR, look at the last hop first. If loss starts at one hop and carries on to the end, the problem is probably at that hop or just after it. If one hop in the middle shows loss but later hops do not, that router is probably just ignoring test messages, and your traffic is fine.

## Good to know

- A row reading `* * * Request timed out` in Traceroute does not always mean a fault. Many routers do not answer test messages.
- Right-click a results table to copy rows or choose **Export to CSV...**. The menu also has shortcuts such as **Traceroute to Target**, **Ping this Hop**, and **Traceroute to Hop**.
- Starting a new run clears the table, so copy or export anything you want to keep first.
- S.A.K. Utility has no tool to view or edit the Windows route table. Traceroute shows the path traffic takes, and nothing more.

## Related guides

- [Look up DNS records and compare DNS servers](https://sakutility.com/wiki/dns-lookup-and-compare)
- [Scan a PC for open ports on Windows](https://sakutility.com/wiki/scan-open-ports)
- [Test internet and LAN speed between two PCs](https://sakutility.com/wiki/test-network-speed)
- [Reset Winsock and TCP/IP on Windows](https://sakutility.com/wiki/reset-network)
