To convert a dynamic disk to basic, change a cluster size, or convert FAT32 to NTFS on Windows, use Partition Manager in S.A.K. Utility: open the Partition Manager tab, select the disk or partition, and click the matching action in Partition Operations. Most of these back up the volume, rebuild it, restore the files, and check them, and all of them wait in the queue until you press Apply.
When to use this
- Convert Dynamic Disk to Basic: a data disk is dynamic, and you want a normal basic disk.
- Change Cluster Size: a volume uses the wrong allocation size for its files.
- Convert File System: a FAT or FAT32 volume needs to become NTFS.
- Convert Primary/Logical: an MBR data disk needs the other partition kind.
- Reformat for New Serial Number: a volume needs a new serial number, for example after cloning.
What you need
- A mounted data partition with a drive letter, on a disk other than the one running Windows.
- For all but Convert File System: a backup folder on a different volume, with room for all the files.
- Administrator approval when you press Apply.
Steps
Each procedure below ends the same way. Optionally press Dry Run, then press Apply, read the Apply Partition Operations window, press Apply in it, and approve the Windows prompt.
Convert a dynamic disk to basic
A dynamic disk shows in the table marked Dynamic, with its volumes. Windows' storage commands leave these disks out, so S.A.K. asks the disk itself. Nothing but this conversion can change one.
- Press Scan Disks and select the disk row. It must hold one mounted simple volume.
- Click Convert Dynamic Disk to Basic. On a basic disk it is grayed out, in the ribbon and in the disk's right-click menu, and its tip says the disk is basic: there is nothing to convert.
- Next to Backup directory:, press Browse and pick a folder on another volume.
- Check I understand this will delete the dynamic volume and rebuild it as basic.
- Press Add to Queue.
Change a cluster size
- Select a partition with a drive letter.
- Click Change Cluster Size.
- Set File system: and Target cluster size:. Add to Queue stays gray if the size is Default. Set Label: if you want to change it.
- Choose a Backup directory: on another volume.
- Check I understand this will reformat the selected volume after backup.
- Press Add to Queue.
The cluster size is the smallest block a file can occupy. Larger clusters suit big files. Smaller ones waste less space on many tiny files.
Convert FAT32 to NTFS
- Select a FAT or FAT32 partition with a drive letter.
- Click Convert File System. It goes straight into the queue.
Convert primary to logical, or logical to primary
- Select the partition. The disk must be MBR and hold only this one partition.
- Click Convert Primary/Logical. The window says which way it will convert.
- Choose a Backup directory: on another volume.
- Check I understand this will clear and rebuild this single-volume MBR data disk.
- Press Add to Queue.
Get a new volume serial number
- Select a partition with a drive letter.
- Click Reformat for New Serial Number.
- Choose a Backup directory: on another volume.
- Check I understand this will reformat the selected volume, then restore and verify files.
- Press Add to Queue.
How it works
Convert File System runs Windows' convert.exe with /NoSecurity /X, which keeps your files where they are. S.A.K. answers its question about the volume's label for you. /X dismounts the volume first, so close anything using it, because open files on it lose unsaved changes.
The others share one approach, because these changes cannot be made in place:
- Copy every file to your backup folder, using a Windows shadow copy (a frozen snapshot of the volume) where the file system supports one.
- Rebuild the volume. That means a reformat for cluster size and serial number, and clearing and recreating the disk layout for the two disk conversions.
- Copy the files back.
- Compare a SHA-256 fingerprint of every file against the backup, and stop with an error if any differ.
- Scan the volume for errors.
Good to know
Back up first. Copy anything you care about to another drive before you press Apply. On the v0.9.3 code, Partition Manager operations, including boot repair, MBR-to-GPT conversion and OS migration, ran through the app on disposable virtual machines and virtual disks. Some operations were also tested on one SAMSUNG MZVL2512HCJQ-00BH1 512 GB NVMe SSD and one Seagate Expansion Desk 8 TB USB disk. Internal SATA drives were not tested, and results on other devices may differ. See what was tested. Applied changes cannot be undone.
- Your files exist only in the backup folder for a time. During a rebuild, the original volume is gone. If the operation stops partway, look in the backup folder.
- Long jobs run as long as they need. A copy, wipe, move, or full format takes as long as the drive takes, which can be days on a large one. Cancel ends it. The backup, rebuild, restore, and fingerprint check all run as one job, and during it the files may exist only in your backup folder.
- Keep the backup folder until you have checked your files. S.A.K. leaves it in place afterwards, so delete it yourself.
- Some things are not copied back. The copy skips junctions (a kind of folder shortcut), so recreate any you rely on.
- FAT32 to NTFS is one way and changes file security. S.A.K. cannot convert back. Because it uses
/NoSecurity, converted files can be opened by all users, so set permissions afterwards if they matter. exFAT is refused. - File system limits. The backup-based tools work on NTFS, FAT32, and exFAT, and Change Cluster Size also offers ReFS.
- A new serial number can affect software. Programs licensed to a volume's serial number may ask you to activate them again.
- A dynamic disk with more than one volume is refused. You see Only one mounted simple dynamic volume can be converted directly. A volume that also lies on another disk is refused when you press Apply, and nothing changes.
- Blocked targets. These tools refuse the disk Windows is running from, and system, boot, EFI, MSR, and recovery partitions. A message then says why.