To clone a disk on Windows, use the Copy Disk Wizard in S.A.K. Utility: open the Partition Manager tab, select the source disk, click Copy Disk Wizard, and choose a target disk at least as large. Use Copy Partition Wizard for one partition. Right-click a disk for image files. All of these wait in the queue until you press Apply.
When to use this
- Copy Disk Wizard: replace a data disk, or keep a spare identical copy. To move the disk Windows runs from, use the migration wizard.
- Copy Partition Wizard: copy one partition into free space on another disk, or to an image file.
- Create Disk Image and Restore Disk Image: save a whole disk to one file and write it back later.
What you need
- A target with nothing on it you want to keep.
- For a disk copy: a target disk at least as large as the whole source disk, not on the disk running Windows.
- For a partition copy: a source partition with a drive letter.
- For images: a place to store the file that is not on the disk being imaged or restored.
- Administrator approval when you press Apply.
Steps
Clone a disk
- Press Scan Disks and select the source disk row.
- Click Copy Disk Wizard. The Source page names the source. Press Next >.
- On Target Disk, choose Target disk: and press Next >. The disk this PC runs from stays in the list, turned off, with the reason beside it. If no other disk can take the copy, Finish stays off and the Review page says why.
- On Options, set Verify: to Sample verification or Full verification, and press Next >.
- On Review, check the summary. Check I understand the selected target disk will be overwritten. and press Finish.
- Press Apply, read the Apply Partition Operations window, press Apply in it, and approve the Windows prompt.
Copy a partition
- Select the source partition. It must have a drive letter.
- Click Copy Partition Wizard. The Source Partition page names it. Press Next >.
- On Target, set Target region:. Pick a Disk ... unallocated entry to copy into free space. Pick Image or custom volume/device path to type a location in Target path:, such as an image file name.
- Press Next >. On Options, set Verify: and press Next >.
- On Review, check I understand the selected target path or region will be overwritten. and press Finish.
- Press Apply as above.
Save a disk or partition to an image file
- Right-click the disk row and choose Create Disk Image, or right-click a partition and choose Create Partition Image.
- Choose where to save the
.imgfile. It cannot be on the source disk. If the file already exists, the save window asks whether to replace it, and Yes replaces it when the job runs. - Press Apply as above.
Restore a disk image
- Right-click the target disk row and choose Restore Disk Image.
- Pick the
.imgfile. S.A.K. reads the whole file to fingerprint it, which can take a while. - Read the question. It shows the file, the sizes, and the SHA-256 fingerprint. Press Yes to queue the restore.
- Press Apply as above.
How it works
All of these copy raw bytes, not individual files, so a copy takes as long as the full size of the source, however little of it is in use. The target disk goes offline during a copy, and everything on it disappears from Windows until the copy finishes. Sample verification compares three blocks. Full verification compares every byte. Create Image always uses full verification.
Creating an image, and copying a partition, lock the source volume first, so nothing can change it during the copy. If a volume is in use and cannot be locked, such as the one Windows is running from, the operation stops with an error. Close what is using it and try again. A read-only partition can be copied, because a copy only reads it.
A restore checks the image's fingerprint again just before writing, and refuses if the file has changed since you approved it.
Good to know
Back up first. Copy anything you care about to another drive before you press Apply. On the v0.9.3 code, Partition Manager operations, including boot repair, MBR-to-GPT conversion and OS migration, ran through the app on disposable virtual machines and virtual disks. Some operations were also tested on one SAMSUNG MZVL2512HCJQ-00BH1 512 GB NVMe SSD and one Seagate Expansion Desk 8 TB USB disk. Internal SATA drives were not tested, and results on other devices may differ. See what was tested. Everything on the target is overwritten, and this cannot be undone.
- Long jobs run as long as they need. A copy, wipe, move, or full format takes as long as the drive takes, which can be days on a large one. Cancel ends it. At 200 MB per second an 8 TB disk takes about 11 hours, and twice that with Full verification. A copy or restore you stop partway leaves the target unusable, and a target disk may stay offline until you bring it back online in Windows Disk Management.
- Disk copies are byte for byte. The target's partitions keep the source's sizes, places, and partition style. On a larger target the extra space stays unallocated.
- A partition copied into free space does not appear as a partition by itself. S.A.K. writes the bytes there but does not add a partition entry. To make it show up, use the write-back page of the Partition Recovery Wizard with the same offset and size.
- Typing a raw path overwrites it. A device path such as
\\.\E:in Target path: writes over that volume. It is refused if the volume is a system volume, is smaller than the source, or is not on the disk list. A whole-disk path such as\\.\PhysicalDrive2is refused here, so choose a free space entry instead. - Restore limits. The image must be on a local drive that appears in the disk list, on a different disk from the target, and no larger than the target. Network locations are refused. It cannot restore over the disk Windows is running from.
- An image takes the full size of the source. A 1 TB disk makes a 1 TB image file, with no compression.