Flash an ISO or disk image to a USB drive

Write an ISO, IMG, WIC, or DSK image, plain or compressed, to a USB drive or SD card with S.A.K. Utility, and check the result.

To flash an ISO or disk image to a USB drive, use the Image Flasher tab in S.A.K. Utility: click Select Image File, click Next, pick the drive, and click Flash!. The app erases the drive, writes the image, and reads it back to check it.

When to use this

Use this to make a bootable Linux or rescue USB, write a disk image to an SD card, or copy one image to several drives. For a Windows installer, read Make a Windows install USB first, because the app writes those a different way.

What you need

  • An image file: .iso, .img, .wic, or .dsk, or one compressed as .gz, .bz2, or .xz. If you do not have one yet, see download a Linux ISO or build a Windows ISO.
  • A USB drive or SD card you can erase, at least as large as the image.
  • Administrator rights. Selecting an image does not need them, but writing does. Click Run as Admin first. If you wait, Flash! offers to restart the app as administrator, and you then select the image and drive again.

Steps

  1. Plug in the USB drive or SD card, and copy off anything you want to keep.

  2. Click Run as Admin in the status bar at the bottom of the window, and approve the Windows prompt.

  3. Open the Image Flasher tab.

    Image Flasher tab on Step 1: Select Image, with three download cards and the Select Image File button
    Step 1: pick a file, or use a card to get one
  4. Click Select Image File and choose your image.

  5. Check the Image Details box. It shows what the app read from the image, such as the OS, size, and boot type.

    Image Details box listing OS, Architecture, Size, Format, Boot Type, File System, Volume Label, Publisher, Created, and Editions for a sample ISO
    Image Details, filled in from the selected file
  6. Click Next.

  7. On Step 2: Select Target Drives, click the drive to write to. To write several drives, click each one. Click a drive again to deselect it.

    Step 2: Select Target Drives with one USB drive listed and selected, and the Show all drives checkbox below the list
    Only removable drives are listed unless you ask for all
  8. Click Flash!.

  9. Read the Confirm Flash - Data Loss Warning box. Check the image name, the drive, and the Method line.

    Confirm Flash dialog naming the image and target drive, with Method: Raw disk imaging and a warning that all data will be permanently erased
    Last chance to stop: nothing has been written yet
  10. Click Yes.

  11. Wait on Step 3: Flashing.... The page shows the current stage, the amount written, and the speed. A progress bar runs in the status bar. A compressed image first shows Reading the compressed image to find its full size..., with nothing being written yet.

    Step 3: Flashing page showing the amount written, the write speed, and a red Cancel button
    Writing, then verifying
  12. When Flash Complete appears, read the Successful and Failed counts.

    Flash Complete page showing Flash completed successfully, one successful drive, none failed, one ejected, and a Flash Another button
    Remove the drive once it says it was ejected
  13. Remove the drive. If the page says Could NOT be ejected, use Safely Remove Hardware in Windows first. If it says Still offline, bring the disk online in Disk Management first, or it shows no drive letter on the next PC.

To write the next one, click Flash Another.

How it works

The app copies the image to the drive byte for byte, replacing everything on it. Before writing, it locks and closes the drive's volumes, then takes the disk offline so Windows cannot touch it mid-write. It brings the disk back online afterward, waiting a few seconds if Windows is still busy with it, and, by default, ejects it. If the disk stays offline, the finished page lists it under Still offline with how to bring it back, and does not eject it.

After writing, it checks the result. By default it reads the whole image back from the drive and compares checksums. You can change this in Image Flasher settings.

With several drives, the app writes one at a time unless you raise Max concurrent writes. If one drive fails, the others still get written.

Good to know

Flashing erases the entire drive, and it cannot be undone. Check the drive name and size on the confirmation screen before you click Yes.

  • System drive: the list hides fixed drives unless you tick Show all drives (including system drive). Your system drive then appears in red as [SYSTEM DRIVE], and Flash! refuses it with an Operation Blocked message. The app also refuses any disk that carries the Windows boot loader.

    Operation Blocked message saying one or more selected drives is your system drive
    The system drive is refused, and no setting turns this off
  • Large drives: a drive over 128 GB triggers Large Drive Selected, because drives that size are usually not USB sticks. You can change the limit in settings.

    Large Drive Selected warning listing a target drive over the size threshold, with Yes and No buttons. For this picture the threshold was lowered to 8 GB in settings; the default is 128 GB
    Answer No if you do not recognize the drive
  • Administrator prompt: if you click Flash! without administrator rights, the Administrator Required box offers to restart the app. Nothing is written until you have restarted and chosen again.

    Administrator Required box asking whether to restart S.A.K. Utility as administrator
    Restarting clears your selection
  • Compressed images: the app reads a .gz, .bz2, or .xz file all the way through before it touches the drive, because these formats do not reliably say how large they unpack to. That can take a few minutes on a large image, and you can cancel it. A damaged file is refused at this stage, and so is a compressed tar archive such as a .tar.gz, because it holds files rather than a disk. Nothing has been written when either happens.

  • ZIP archives: these are refused when you select them. Extract the image from the archive first.

  • Apple .dmg images: a real .dmg is refused when you select it, because it is not a disk until it is converted. On a Mac, convert it with hdiutil convert -format UDTO.

  • Other file types: if the app does not recognize a file's type, it asks Unable to detect image format. Continue anyway? Say Yes only if you know the file is a raw disk image.

  • Image too big: a drive smaller than the image fails with Image is larger than the target device, and nothing is written to it. For a compressed image, the size that counts is the unpacked one.

  • Flash Error: a message saying Nothing was written to the target drive. means the run stopped before any writing began, so the drive is as it was.

  • Boot Type in Image Details describes what the image says it supports. It is not a promise about any particular PC.

  • Cancel: press the red Cancel on Step 3: Flashing... and answer Yes. The page says Stopping the write... until the write stops, then Flash Cancelled says what the drive holds: Nothing was written means it is as it was; Writing had started means it will not work until you flash it again or format it.

  • Using the drive normally again: after a raw write, Windows may show a small partition or offer to format the drive. To get the full capacity back, delete the partitions and format it.