Set a static IP, DNS, or DHCP on a network adapter

Set a static IP, change DNS, switch to DHCP, rename or disable a network adapter from the Network Adapters tab in S.A.K. Utility.

To change a network adapter's settings, use S.A.K. Utility: go to the Network Management tab, open Network Adapters, right-click the adapter, and choose IP Configuration. From that menu you can set a static IP address, set DNS servers, or switch back to automatic settings. The same right-click menu can also disable or rename the adapter.

When to use this

  • A printer, server, or similar device needs a fixed address.
  • You want a PC to use different DNS servers.
  • You want to see everything about an adapter in one place.

A static IP is an address you set by hand. DHCP is the usual automatic setting, where the router hands out an address.

What you need

  • Administrator rights for any change. S.A.K. Utility does not ask for them on its own here, so click Run as Admin in the status bar first. Without them, the change fails with a message saying that administrator rights are needed.
  • The correct address, subnet mask, and gateway for your network, if you are setting them by hand.

Viewing adapters needs no special rights.

Steps

See your adapters

  1. Go to the Network Management tab and open Network Adapters.

  2. Read the table: Name, Type, Status, IP Address, MAC, and Speed. MAC is the adapter's hardware ID. Status reads No valid address when the adapter is connected but has only a self-assigned 169.254.x.x address: Windows gave it that because no DHCP server answered and no address is set by hand, so it cannot reach other networks. Point at the status or the address to read why.

    The adapter table with the Ethernet adapter's status reading No valid address in orange beside the self-assigned address 169.254.193.132, and the loopback adapter Connected
    An adapter with only a self-assigned address
  3. Click an adapter to see more below the table, including its gateway, DNS servers, and whether DHCP is on.

  4. Press Refresh Adapters or F5 to read them again. Press Copy Config to copy the details as text.

Network Adapters tab with toolbar buttons, a table of adapters, and details of the selected adapter below
The Network Adapters tab with one adapter selected

Open the adapter menu

Right-click an adapter. What you see depends on its type. Wi-Fi and Ethernet adapters have IP Configuration, and Bluetooth adapters have View Bluetooth Devices.

Right-click menu for an Ethernet adapter with Status, Properties, Disable, Diagnose, IP Configuration, Rename, Copy Configuration, Backup Settings, and Restore Settings
The right-click menu for an Ethernet adapter

Choose Status... for a full report on the adapter: connection, addresses, DHCP lease, traffic counts, errors, and driver details.

Adapter Status window with General, Connection, IPv4 Configuration, and IPv6 Configuration in view, and more sections further down
Status... shows everything Windows reports about the adapter

Scroll down in that window for DHCP, Statistics, and Driver Information.

Set a static IP address

A wrong address can cut this PC off from the network. If you are connected to the PC remotely, you may lose the connection.

  1. Right-click the adapter and choose IP Configuration, then Set Static IP....
  2. Fill in IP Address, Subnet Mask, and Gateway. The boxes start with the current values.
  3. Press OK.
Set Static IP window with boxes for IP Address, Subnet Mask, and Gateway, and OK and Cancel buttons
Set Static IP starts with the adapter's current values

Set DNS servers

  1. Right-click the adapter and choose IP Configuration, then Set DNS Servers....
  2. Fill in Primary DNS. Secondary DNS is optional.
  3. Press OK.
Set DNS Servers window with boxes for Primary DNS and Secondary DNS, and OK and Cancel buttons
Set DNS Servers takes one required and one optional server

Go back to automatic settings

  1. Right-click the adapter and choose IP Configuration, then Enable DHCP. This item appears only when DHCP is off.
  2. Press Yes. The static settings are removed.

When DHCP is on, the same menu has Release DHCP Lease and Renew DHCP Lease, which give up the current address and ask for a new one.

Other menu items

  • Disable or Enable turns the adapter off or on. Disabling asks first, because you may lose your connection.
  • Rename... changes the adapter's name.
  • Properties and Open Adapter Settings open the matching Windows settings page.
  • Diagnose starts a Windows network troubleshooter. Where Windows no longer has that troubleshooter, it opens Settings at Troubleshoot instead and the status bar says so.

How it works

S.A.K. Utility passes each change to Windows, then reads the adapters again so the table shows the result. The other toolbar buttons, Backup Settings, Restore Settings, and Reset Network, have guides of their own below.

Good to know

  • Static IP and DNS changes here cover IPv4 only.
  • The gateway in Set Static IP... is the only routing setting. S.A.K. Utility has no route table editor.
  • Set Static IP... leaves the gateway's priority (its metric) to Windows, as Windows' own adapter settings do, so on a PC with more than one network it does not take over the default route.
  • Save the current settings first if you might want them back. See the backup guide below.
  • S.A.K. Utility does not create network bridges. To make one, choose Open Adapter Settings, select the adapters in the Windows window that opens, right-click, and choose Bridge Connections.