Test internet and LAN speed between two PCs

Measure internet speed, or LAN speed between two PCs with iPerf3 or LAN Transfer, in S.A.K. Utility. LAN Transfer tests speed only and copies no files.

To test network speed, use S.A.K. Utility: go to the Network Management tab, open Network Diagnostics, and choose Bandwidth or LAN Transfer. Use Run Speed Test for your internet speed. For a speed test between two PCs on the same network, use iPerf3 or LAN Transfer. LAN Transfer is a speed test only. It does not copy your files.

When to use this

You want to know Use You need
How fast this PC's internet is Internet Speed (HTTP) on the Bandwidth tab Internet
How fast two PCs talk, with jitter and packet loss LAN Bandwidth (iPerf3) on the Bandwidth tab A second PC running an iPerf3 server
How fast two copies of S.A.K. Utility can send data LAN Transfer A second PC running S.A.K. Utility

What you need

  • For a test between two PCs: both on the same network, and the receiving PC's IP address. You can find it on the Network Adapters tab.
  • iPerf3 comes with S.A.K. Utility, so a second copy of the app can act as the server. iPerf3 is a common tool for measuring network speed.
  • For an iPerf3 server that another PC connects to: administrator rights. Click Run as Admin in the status bar first. The server adds a Windows Firewall rule so the other PC can reach it, and adding the rule needs these rights. LAN Transfer and the internet test do not need them.

Steps

Test your internet speed

  1. Go to the Network Management tab and open Network Diagnostics.
  2. Choose the Bandwidth tab.
  3. Under Internet Speed (HTTP), press Run Speed Test.
  4. Read Download, Upload, and Latency when it finishes. Latency is the delay before a response starts. The numbers stay on screen until you run another test.
Bandwidth tab with the LAN Bandwidth (iPerf3) form above and an Internet Speed (HTTP) result showing download, upload, and latency
The Bandwidth tab holds both the iPerf3 test and the internet speed test

Test two PCs with iPerf3

On the PC that receives the test:

  1. Open the Bandwidth tab.
  2. Leave Port at 5201, or choose another.
  3. In Listen on:, choose the network adapter the other PC can reach. Each connected adapter is listed by its name and IP address. The list starts on the adapter that holds this PC's default route, or on the one you used last time for this server.
  4. Press Start Server. The label changes to Server: Running on port 5201.

If S.A.K. Utility is not running as administrator, the label reads Server: Stopped (needs Run as Admin) before you start. Start Server then starts nothing, and the status bar says Run as Admin to start the iPerf3 server: adding its firewall rule needs administrator rights. Click Run as Admin and start the server again. A server on 127.0.0.1, which only this PC can reach, needs no administrator rights.

The Bandwidth tab in a Standard session after Start Server was pressed, with the status bar and the log window both reading Run as Admin to start the iPerf3 server: adding its firewall rule needs administrator rights
Without administrator rights, Start Server says what it needs

On the other PC:

  1. Open the Bandwidth tab.
  2. Type the receiving PC's address in Server, and use the same Port.
  3. Set Duration (10 s by default) and Streams (1).
  4. Leave Bidirectional ticked to test both directions at once.
  5. Press Run Test.

You get Download, Upload, Jitter, Packet Loss, and Retransmits. They stay on screen until you run another test. The server handles one test and then stops, so press Start Server again for another run.

Test two PCs with LAN Transfer

On the PC that receives the test:

  1. Choose the LAN Transfer tab.
  2. Under LAN Transfer Server (Receiver), in Listen on:, choose the network adapter the sending PC can reach, as for iPerf3.
  3. Leave Listen Port at 5050, or choose another.
  4. Press Start Server. The label shows Server: Running on port 5050.

On the PC that sends:

  1. Choose the LAN Transfer tab, and set Listen Port to the same number. The test connects to that port.
  2. Under LAN Transfer Client (Sender), type the receiving PC's address in Target.
  3. Set Duration (10 s by default) and Block Size (64 KB).
  4. Press Run Transfer Test.

You get the amount sent, the time taken, Average Speed, and Peak Speed. On the receiving PC, press Stop Server when you finish.

LAN Transfer tab with the Receiver section showing Listen Port and a stopped server, and the Sender section showing Target, Duration, and Block Size
LAN Transfer has a receiver section and a sender section

How it works

The internet test downloads and uploads small amounts of test data from Cloudflare's public speed service and times them. It uses little data, so treat it as a quick check.

The iPerf3 test runs the iPerf3 program on both PCs, and they measure the link between them.

Both servers listen only on the adapter chosen in Listen on:, not on every network the PC is on. As its tooltip says, other devices reach the server at that address only, and it is not open on the PC's other networks. The iPerf3 server also drops a client that connects and then goes quiet, so a stalled connection cannot hold it.

LAN Transfer sends made-up data from one PC to the other for the time you set. The receiver counts it and throws it away. No file is sent or saved.

Good to know

  • The internet test and the iPerf3 test share one worker, so while one runs, neither Run button can be pressed. Stop can take a moment, and the buttons come back once the test has really stopped.
  • A test you stop, or one that could not finish, says No result. The test was stopped or could not finish. If the delay could not be measured, Latency says unknown.
  • Generate Report... at the bottom of the tab includes the last speed test result. See the network report guide below.
  • To copy real files between PCs, use Windows file sharing or a USB drive. LAN Transfer does not do it.
  • Before the iPerf3 server starts, S.A.K. Utility adds a temporary Windows Firewall rule, and the server starts only once the rule is in place. The rule lets in only the bundled iPerf3, on the address and port you chose, from devices on the same subnet, on private networks. It is removed when the server stops. A server on 127.0.0.1 needs no rule. If Windows refuses the rule while S.A.K. Utility is running as administrator, the status bar says iPerf3 server not started: Windows Firewall did not add its inbound rule: followed by Windows' own reason.
  • LAN Transfer adds no firewall rule, so Windows Firewall may ask for permission on the receiving PC, or block the test.
  • If LAN Transfer reports that the connection timed out, check that the server is running on the other PC, and that both use the same port.
  • Wi-Fi results change a lot from moment to moment. Run a test more than once before you trust a number.